Flow circuit equipment

For concrete swimming pools

Skimmers, 15 l.

Skimmer open elements are made of UV-rays-resistant material. Recommended water flow – 5000 l/h. Skimmer lid regulates water upper level. Lower suction pipe: inner junction 1 1/2", outer junction 2". Drainage socket - Ø 50. Upper socket with diameter Ø 40 is for additional drainage overflow. Skimmer basket is fixed with a bayonet socket. Skimmer basket filtrates big pollutions.

With a standard inlet: With a round lid With a square lid code 00249 code 00250 With an extended inlet: With a round lid With a square lid code 00251 code 00252

Skimmers, 17,5 l.

Skimmer open elements are made of UV-rays-resistant material. Recommended water flow – 7500 l/h. Skimmer lid regulates water upper level. Lower suction socket: inner junction 1 1/2", outer junction 2". Drainage socket with diameter Ø 32 for additional drainage. Skimmer basket is fixed with a bayonet socket. A skimmer lid has a spring pin. Lid level is regulated with additional insertions.

With a standard inlet: With a round lid With a square lid code 05589 code 11306 With an standard inlet and a front panel: With a round lid With a square lid code 05280 code 11302 With an elongated standard inlet: With a round lid With a square lid code 05590 code 11307 With an elongated standard inlet and a front panel: With a round lid With a square lid code 05281 code 11303

Stainless steel skimmer AISI – 316

Skimmer A – 100 made of stainless steel AISI – 316. A set includes a drain socket, a plastic basket and a lid. Drainage socket with diameter Ø50. Suction socket 2”. Skimmer has points for ground connection. Regulating valve (level 00256) installation is possible. code 00254 Overlay Stainless steel AISI – 316 for skimmer 00254             code 00255

Inlets made of ABS – plastic

Suction inlet made of white ABS – plastic for glueing with pipe Ø63 and Ø50. Maximum pressure – 6 bar. Screw lid 1 1/2". Recommended to be installed with an embedded pipe 15661-15660. code 00300

Bottom inlet

Bottom inlet is made of white ABS – plastic with outer thread 2" and inner diameter of Ø50, stainless steel screws. Designed for water inlet. Flow is regulated with a central screw. Junction 2", max. flow 14m³/h Junction 1 1/2", max. flow 9m³/h code 00303

Stainless steel inlet

Inlet made of stainless steel AISI – 316 with outer thread 1 1/2". Recommended flow 5m³/h. Ball with an opening Ø20 mm. Length 50 mm Length 70 mm code 16325 code 16326

Cross grating

Grating module Modules are connected with ropes (49 items = 1m) Height 22 mm, width 195 mm code 00212 Height 22 mm, width 245 mm code 00213

Grating module for bending Modules are connected with cables (49 items = 1m) Height 22 mm, width 195 mm Height 22 mm, width 245 mm Height 22 mm, width 295 mm Height 22 mm, width 335 mm code 11107 code 11108 code 19202 code 19203

Grating module for bending Modules are connected with cable (45 items = 1 m) Height 35 mm, width 195 mm Height 35 mm, width 245 mm Height 35 mm, width 295 mm Height 35 mm, width 335 mm code 00220 code 00221 code 00222 code 00223

Bottom outlets

Round bottom outlet Lower socket 1 1/2", side socket 2" Maximum productivity 15m³/h code 01466 Bottom outlet is made of white ABS-plastic. Lower socket allows to install hydrostatic valve and a drainage pipe. Bottom outlet grating Ø250.

Round stainless steel bottom outlet Pipe 2" Case and grating made of stainless steel AISI – 316 Grating is fixed with screws. code 00268